It is excellent for riveting, flattening, forging, and forming metal. It is widely used by metalworkers and smiths in any metal shop. Wide Application: The anvil is ideal for hammering, straightening, and for shaping workpieces.The wide countertop and flat surface provide a better user experience. Large Working Area: This anvil metal 110 lbs/50 kg forge comes with a comfortable and wide work surface, giving a large working area.And the spray coating effectively relieves the oxidation reaction. Polishing Treatment: With fully polished surface area, the blacksmith anvil is corrosion-proof and services long-lasting use through quenching treatment.And the hardy hole and pritchel hole can show a good performance in accessories’ punching and twisting. Holes & Horns for Different Uses: Round horn and the flat horn of the anvil blacksmith are used for smoothing, bending, and shaping.Our steel anvil blacksmith has excellent grade material of 50 HRC. Premium Material 110 lbs: This steel anvil is made of drop-forged, high-grade steel, which features high hardness, strength, and durability.Now that I think about it, with L-56 the unit did have some minor arc starting issues. I tried L-56 on the unit, and the results was very unsatifactory. 030 solid wire ( HB-28 or Radnor) and C-25, the MM 180 is a real nice 1/8" or. Still though, the top end arc, and weld puddle wet out are definitely better on the MM 180, then they are on the MM 175. In my experience, the unit fired off a solid arc start everytime, when holding a stick out in the 1/4" - 1/2" range, even when the base metal had a light coating of soot on it.Ĭompared to the results the HH 187 produces, the top end spatter level could definitely be considered on the high side. Matter of fact, I felt its solid arc starts were one of it strong points. I field tested a MM 180 for at least 6 months, and I experienced no arc starting issues from the unit. Once its going, its beautiful.Lotta spatter on top end too.Tom, I can honestly state, 10 out of 10 times, I would without hesitation choose the HH 187 over the MM 175.īTW, I have quite a few hours put in on both units.ĭan, My MM180 is also finniky on the starts.Even worse when im on thin gauge. Atlas Knife and Tool, Cliff Carroll, NC Tool Co Emerson Scott And more If you are specifically interested in bladesmithing, Centaur Forge also offers a selection of knifemaking anvils to help you craft your perfect blade. Weld puddle wetout on the top end is very good, and the spatter level is extremely low for the out put power level that the top end is capable of producing. The HH187 produces a very smooth consistent arc through out all 7 voltage taps. Once again as long as you have it tuned in properly, and are running a good wire, you should never experience harsh arc characteristic from the HH 187. As long as you have the unit set up properly, and the voltage to wire speed ratio dialed in reasonably to the right proportion, poor arc starts from the HH 187 should never be an issue. No matter your skill level though, between these two units, the HH 187 will always be the much easier unit to dial a solid arc in on. In contrast, the HH 187, depending on your skilll level, can be quite simple to dial a very solid arc in on. The MM 175 is very finnicky in the area of arc starts.The top end performance on the MM 175 is pretty rough too, meaning the arc is harsh, the weld puddle doesn't wet out very well, and there is quite a bit of spatter. The MM 175 is a nightmare to deal with, when it comes to tune in the arc properly. and it has two horns, which is a plus, its an Italian pattern anvil, as seen by a chinese manufacturer. The 187 is most definitely the better of the two, and it isn't even a close contest. well, at that price it would be a decent anvil in spite of the flaws.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |